RSRP and RSRQ Measurement in LTE

الخميس أكتوبر 29, 2015 7:11 pm

[ltr]In cellular networks, when a mobile moves from cell to cell and performs cell selection/reselection and handover, it has to measure the signal strength/quality of the neighbor cells.
In LTE network, a UE measures two parameters on reference signal: RSRP (Reference Signal Received Power) and RSRQ (Reference Signal Received Quality).[/ltr]

[ltr]In LTE network, a UE measures two parameters on reference signal:[/ltr]

[ltr]RSSI - Received Signal Strength Indicator:The carrier RSSI (Receive Strength Signal Indicator) measures the average total received power observed only in OFDM symbols containing reference symbols for antenna port 0 (i.e., OFDM symbol 0 & 4 in a slot) in the measurement bandwidth over N resource blocks.[/ltr]

[ltr]The total received power of the carrier RSSI includes the power from co-channel serving & non-serving cells, adjacent channel interference, thermal noise, etc. Total measured over 12-subcarriers including RS from Serving Cell, Traffic in the Serving Cell[/ltr]

[ltr]RSRP - Reference Signal Received Power: RSRP is a RSSI type of measurement, as follows there are some definition of it and some details as well.
It is the power of the LTE Reference Signals spread over the full bandwidth and narrowband.
A minimum of -20 dB SINR (of the S-Synch channel) is needed to detect RSRP/RSRQ[/ltr]

[ltr]RSRQ - Reference Signal Received Quality: Quality considering also RSSI and the number of used Resource Blocks (N) RSRQ = (N * RSRP) / RSSI measured over the same bandwidth. RSRQ is a C/I type of measurement and it indicates the quality of the received reference signal. The RSRQ measurement provides additional information when RSRP is not sufficient to make a reliable handover or cell reselection decision. [/ltr]

[ltr]In the procedure of handover, the LTE specification provides the flexibility of using RSRP, RSRQ, or both. [/ltr]

[ltr]It must to be measured over the same bandwidth:[/ltr]

- - Narrowband N = 62 Sub Carriers (6 Resource Blocks)
  - Wideband N = full bandwidth (up to 100 Resource Blocks / 20 MHz)
  - [size=30]RSRP[/size]
    
    In other words RSRP (Reference Signal Receive Power) is the average power of Resource Elements (RE) that carry cell specific Reference Signals (RS) over the entire bandwidth, so RSRP is only measured in the symbols carrying RS.
    - - RSRP is the average received power of a single RS resource element.
        UE measures the power of multiple resource elements used to transfer the reference signal but then takes an average of them rather than summing them.
        Reporting range -44…-140 dBm
    RSRP does a better job of measuring signal power from a specific sector while potentially excluding noise and interference from other sectors.
    RSRP levels for usable signal typically range from about -75 dBm close in to an LTE cell site to -120 dBm at the edge of LTE coverage.
    RSRP mapping 3GPP TS 36.133 V8.9.0 (2010-03)
    
    The reporting range of RSRP is defined from -140 dBm to - 44 dBm with 1 dB resolution.
    The mapping of measured quantity is defined in the table.
    [url=http://www.laroccasolutions.com/images/training/RSRP Table.png][/url]
    
    [size=30][ltr]RSRQ[/ltr][/size]
    
    [ltr]In formula:[/ltr]
    
    RSRQ = N x RSRP / RSSI
    - - N is the number of Physical Resource Blocks (PRBs) over which the RSSI is measured, typically equal to system bandwidth
        RSSI is pure wide band power measurement, including intracell power, interference and noise
        The reporting range of RSRQ is defined from -3…-19.5dB
    [url=http://www.laroccasolutions.com/images/training/RSRQ reporting range.png][/url]
    
    [ltr]Reference Signals recap: OFDMA Channel Estimation[/ltr]
    
    [ltr]In simple terms the Reference Signal (RS) is mapped to Resource Elements (RE). This mapping follows a specific pattern (see to below).[/ltr]
    
    [ltr]So at any point in time the UE will measure all the REs that carry the RS and average the measurements to obtain an RSRP reading.[/ltr]
    - - Channel estimation in LTE is based on reference signals (like CPICH functionality in WCDMA)
        Reference signals position in time domain is fixed (0 and 4 for Type 1 Frame) whereas in frequency domain it depends on the Cell ID
        In case more than one antenna is used (e.g. MIMO) the Resource elements allocated to reference signals on one antenna are DTX on the other antennas
        Reference signals are modulated to identify the cell to which they belong.
    [url=http://www.laroccasolutions.com/images/training/RS & RE Distribution.png][/url]
    
    [url=http://www.laroccasolutions.com/images/training/OFDMA Channel RSRP.png][/url]
    
    [ltr]RSSI (Received Signal Strength Indicator) is a parameter which provides information about total received wide-band power (measure in all symbols) including all interference and thermal noise.[/ltr]
    
    [ltr]RSSI is not reported to eNodeB by UE. It can simply be computed from RSRQ and RSRP that are, instead, reported by UE.[/ltr]
    
    [ltr]RSSI = wideband power = noise + serving cell power + interference power[/ltr]
    
    [ltr]So, without noise and interference, we have that 100% DL PRB activity: RSSI=12*N*RSRP[/ltr]
    
    [ltr]Where:[/ltr]
    - - RSRP is the received power of 1 RE (3GPP definition) average of power levels received across all Reference Signal symbols within the considered measurement frequency bandwidth
        RSSI is measured over the entire bandwidth
        N: number of RBs across the RSSI is measured and depends on the BW
    [ltr]Based on the above, under full load and high:[/ltr]
    
    [ltr]SNR: RSRP (dBm)= RSSI (dBm) -10*log (12*N)[/ltr]
    
    [ltr]Impact of serving cell power to RSRQ:[/ltr]
    
    [ltr]Example for noise limited case (no interference): If all resource elements are active and are transmitted with equal power, then[/ltr]
    
    [ltr]RSRQ = N / 12N = -10.8 dB for 1Tx[/ltr]
    
    [ltr]RSRQ = N / 20N = -13 dB for 2Tx taking DTX into account[/ltr]
    
    [ltr](because RSRP is measured over 1 resource element and RSSI per resource block is measured over 12 resource elements).[/ltr]
    
    [ltr]Remember that RSSI is only measured at those symbol times during which RS REs are transmitted - We do not have to take into the count DTx!!![/ltr]
    
    [ltr]So, when there is no traffic, and assuming only the reference symbols are transmitted (there are 2 of them within the same symbol of a resource block) from a single Tx antenna then the RSSI is generated by only the 2 reference symbols so the result becomes[/ltr]
    
    [ltr]RSRQ = N / 2N = -3 dB for 1Tx[/ltr]
    
    [ltr]RSRQ = -6dB for 2Tx[/ltr]